Expanding a (EMC Celerra/VNX) NAS Pool

In this post let’s discuss expanding a (EMC Celerra/VNX-File) NAS pool by adding new LUNs from the backend storage. A NAS Pool from on which we create Filesystems for NFS/CIFS (SMB) should have sufficient space for catering the NAS requests. Here our pool is running out of space, with only a few MBs left.

[[email protected] ~]$ nas_pool -size Bforum_Pool
id = 48
name = Bforum_Pool
used_mb = 491127
avail_mb = 123
total_mb = 491250
potential_mb = 0
[[email protected] ~]$

Let’s see how we can get this pool extended.

Let’s have a look first at the existing disks (LUNs from backend). Here we already have 9 disks assigned. We should have the 10th one in place, which will add up space to the pool.

[[email protected] ~]$ nas_disk -l
id inuse sizeMB storageID-devID type name servers
1 y 11263 CKxxxxxxxxxxx-0000 CLSTD root_disk 1,2
2 y 11263 CKxxxxxxxxxxx-0001 CLSTD root_ldisk 1,2
3 y 2047 CKxxxxxxxxxxx-0002 CLSTD d3 1,2
4 y 2047 CKxxxxxxxxxxx-0003 CLSTD d4 1,2
5 y 2047 CKxxxxxxxxxxx-0004 CLSTD d5 1,2
6 y 32767 CKxxxxxxxxxxx-0005 CLSTD d6 1,2
7 y 178473 CKxxxxxxxxxxx-0010 CLSTD d7 1,2
8 n 178473 CKxxxxxxxxxxx-0011 CLSTD d8 1,2
9 y 547418 CKxxxxxxxxxxx-0007 CLSTD d9 1,2
[[email protected] ~]$

As per the requirement, we have to assign the LUNs from the backend storage. It is recommended to add the new LUNs of identical size as of existing LUNs in the pool to have best performance.

Now to the most important part – Rescaning the new disks. We have to use the server_devconfig command for rescan. We can run the command against individual data movers also. The recommeded way to do this is to start with the standby DMs first and then on primary ones. Listing the nas_disks will show the servers on which the disks are scanned.

[[email protected] ~]$ server_devconfig ALL -create -scsi -all

Discovering storage (may take several minutes)
server_2 : done
server_3 : done
[[email protected] ~]$

Yes, that is done successfully. Now let’s check the disks list. We can see the 10th disk with inuse=n which is scanned on both servers (data movers).

[[email protected] ~]$ nas_disk -l
id inuse sizeMB storageID-devID type name servers
1 y 11263 CKxxxxxxxxxxx-0000 CLSTD root_disk 1,2
2 y 11263 CKxxxxxxxxxxx-0001 CLSTD root_ldisk 1,2
3 y 2047 CKxxxxxxxxxxx-0002 CLSTD d3 1,2
4 y 2047 CKxxxxxxxxxxx-0003 CLSTD d4 1,2
5 y 2047 CKxxxxxxxxxxx-0004 CLSTD d5 1,2
6 y 32767 CKxxxxxxxxxxx-0005 CLSTD d6 1,2
7 y 178473 CKxxxxxxxxxxx-0010 CLSTD d7 1,2
8 n 178473 CKxxxxxxxxxxx-0011 CLSTD d8 1,2
9 y 547418 CKxxxxxxxxxxx-0007 CLSTD d9 1,2
10 n 547418 CKxxxxxxxxxxx-0006 CLSTD d10 1,2
[[email protected] ~]$

Let’s check the pool again to see the available and potential storage capacity.

[[email protected] ~]$ nas_pool -size Bforum_Pool
id = 48
name = Bforum_Pool
used_mb = 491127
avail_mb = 123
total_mb = 491250
potential_mb = 547418
[[email protected] ~]$

Now, as you see, the expanded capacity is available in the pool (refer the potential storage) .

You may refer to our previous post on scanning new LUNs on VNX File/Celerra Data movers. click here for more Celerra/VNX posts.

Leave a comment :